How to Check Battery Cycle Count on the DJI Neo 2
Peter Leslie
21 May 2026
If you are wondering whether your DJI Neo 2 battery is fresh or worn, the cycle count is the number you want, and it lives one menu path deep inside DJI Fly. The cycle count is the running total of full charge-and-discharge cycles the pack has been through, and most drone pilots use it to decide when a pack is ready to retire — a brand-new battery on the DJI Neo 2 reads zero, and the number climbs by one each time the pack receives the equivalent of a full cycle.
The check itself takes about fifteen seconds once the drone is talking to the phone. Tap into Settings, drop into the Safety category, scroll past the flight-limit blocks, and the Battery Info section carries the Cycle Count row at the very bottom. The same screen is the one to revisit before any long-term battery storage decision or any out-of-warranty pack swap.
Quick guide
To check the battery cycle count on the DJI Neo 2, go to DJI Fly → Settings → Safety → Battery Info → Cycle Count. A brand-new pack reads zero; the integer climbs by one for every full charge-and-discharge equivalent the battery has been through.
Step-by-step: How to Check Battery Cycle Count on the DJI Neo 2
Follow these top to bottom the first time, and you will know the path off by heart the second time.
Power the DJI Neo 2 on and pair the remote with the phone
Press and release the power button on the DJI Neo 2, then long-press to bring the drone up. Switch the remote controller on and wait for DJI Fly on the phone to show the connection banner. The Battery Info screen only populates the smart-battery rows once the drone is actively connected, so the link has to land before the cycle count appears.
Launch DJI Fly and tap Go Fly to enter the camera view
Open DJI Fly on the phone. The home screen lists the connected DJI Neo 2 and a large Go Fly button near the bottom. Tap Go Fly to drop into the camera view — the live feed fills the screen and the Settings entry point appears in the top-right corner.
Open the DJI Fly Settings menu from the camera view
Tap the three-dot Settings icon sitting in the top-right corner of the camera view. The Settings panel slides in from the right side of the screen and lists every category down the left edge — Safety, Control, Camera, Transmission, and About.
Select the Safety category from the left side of the Settings panel
Tap Safety from the category list. The right pane refreshes with every safety-related setting on the DJI Neo 2 — flight limits, signal-lost behaviour, advanced safety actions, and the battery information block. Safety is usually the first or second entry on the category list.
Scroll down to the Battery Info section near the bottom of Safety
Drag the right pane upwards to scroll past the flight-limit and signal-lost blocks. Battery Info sits near the bottom of the Safety category because it carries read-only data rather than an in-flight setting. Tap the Battery Info header to expand the section.
Read the Cycle Count row at the bottom of the Battery Info screen
The Cycle Count row sits at the very bottom of the Battery Info section and shows a single integer to the right of the label. A brand-new pack reads zero, a worked-in pack reads anywhere from one upwards, and a pack approaching retirement on the DJI Neo 2 will be sat in the high hundreds. Note the number against the serial sticker on the pack so you can compare batteries across a multi-pack kit later.
Swap each pack into the drone and repeat the check across the kit
Power the DJI Neo 2 down, eject the current pack, slot the next pack, and bring the drone back up. Re-open Settings → Safety → Battery Info and the Cycle Count row refreshes to match the newly installed pack — each battery carries its own independent count on its smart-battery chip. Working through the kit one pack at a time builds an honest ordering of which battery is freshest and which one is the next to retire.
Peter's tip
I write the cycle count on a small label stuck to each DJI Neo 2 pack and update it every month or so. It takes thirty seconds per battery and it kills the guesswork — the freshest pack always goes on the longest leg of the job, the highest-count pack stays as the hover-and-test-shots backup, and there is no debating which one to leave behind when a job calls for two batteries instead of three.
Frequently asked questions
What counts as one battery cycle on the DJI Neo 2?
One cycle is the equivalent of a full discharge plus a full recharge on the DJI Neo 2 battery, not a single plug-in. Two half-charges count as one cycle, four quarter-charges count as one cycle, and a top-up from eighty percent does not tick the counter at all. The Cycle Count row inside Battery Info aggregates partial sessions internally, so the integer on screen always reflects full-cycle equivalents rather than raw charge events.
How many cycles does a DJI Neo 2 battery last before it needs replacing?
DJI rates the Neo 2 Intelligent Flight Battery for around two hundred full charge cycles before the usable capacity drops below the threshold most drone pilots will tolerate. The pack will still take a charge well beyond that number, but the flight time per pack starts shrinking visibly and the low-battery RTH triggers earlier into the flight. Most drone pilots replace the pack once the count crosses two hundred and the recorded flight time per battery has dropped by a noticeable margin.
Does each battery on the DJI Neo 2 have its own cycle count?
Yes. The Cycle Count row reads off the smart-battery chip inside whichever pack is currently slotted into the DJI Neo 2, so each battery carries its own independent count. Swap a fresh pack into the drone, refresh the Battery Info screen, and the number changes to match the new pack. This is why drone pilots who fly a multi-pack kit usually check each battery in turn before a job — the oldest pack is rarely the one with the lowest count.
Why does the DJI Neo 2 Cycle Count not move after a quick top-up charge?
The counter only ticks on full-cycle equivalents — a quick top-up from eighty percent to a hundred adds twenty percent of one cycle to the internal tally, not a whole cycle. The integer on the Battery Info screen only changes once the cumulative partial charges add up to a full cycle. A pack that gets topped up regularly will see the counter move in jumps every few flights, not after every single charge.
Can I reset the Cycle Count on the DJI Neo 2 battery?
No. The cycle count is held on the smart-battery chip inside the pack and is not user-resettable on the DJI Neo 2 — neither DJI Fly, the firmware updater, nor a hard reset of the drone touches the number. This is by design, because the count is the load-bearing input for the battery health calculation and the warranty assessment. A pack that has supposedly never been used but shows a non-zero count has been used.
What if the Cycle Count row is missing from the Battery Info screen on the DJI Neo 2?
If the Cycle Count row is not showing, the most common cause is that the drone is not actually connected to DJI Fly — Battery Info shows the static fields only and hides the smart-battery data until the live link is up. Power the DJI Neo 2 on, confirm the connection banner inside DJI Fly, and re-open Settings → Safety → Battery Info. If the row is still missing, update DJI Fly to the latest version — older builds occasionally hid the row on certain firmware combinations.
Should I worry about a high Cycle Count if the DJI Neo 2 battery still flies well?
Cycle count is one signal, not the whole story — the more honest test is recorded flight time per pack and the percentage on landing for the same flight profile. A high-count pack that still hits its rated flight time and lands above the low-battery threshold is fine to keep using. A high-count pack that lands two minutes earlier than its siblings on the same flight, or that triggers low-battery RTH at sixty percent indicated, is the one to retire — the Cycle Count row is the early warning, not the verdict.
The Cycle Count row is the cheapest honesty check available on the DJI Neo 2 — fifteen seconds inside Settings tells you which pack is fresh, which one is worked in, and which one is on its way out. Build the habit of checking each pack once a month, label the numbers on the batteries themselves, and the kit will tell you when it is time to order a replacement long before a flight goes short.
If a Cycle Count row reads suspiciously low on a pack you bought second-hand, or suspiciously high on a pack still in warranty, drop the details to peter@hiredronepilot.uk and I will come back to you directly. The video version of this walkthrough is on YouTube and the comments are open.
References
Primary source material for this article is the official DJI Neo 2 documentation and DJI Fly. External links open in a new tab.
- DJI Neo 2 — Downloads (User Manual, Quick Start Guide, firmware notes) · Battery Info screen behaviour, Cycle Count field definition, and Intelligent Flight Battery cycle ratings.
- DJI Neo 2 — Specifications (UK) · Battery chemistry, capacity, and rated cycle life for the DJI Neo 2 Intelligent Flight Battery.
- DJI Fly — App download and release notes · The app that hosts the Settings → Safety → Battery Info screen where the Cycle Count row lives. Release notes flag any layout changes between app versions.
Peter Leslie
Founder & GVC Drone Pilot
Peter is the founder of HireDronePilot. With thousands of logged commercial flight hours, he writes about drone technology, commercial surveying tactics, and UK aviation compliance.
Connect on LinkedIn